Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 9 - Jul 14
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
HobbyWing XRotor Convertible F7/65A HD AM32 Stack DJI PNP - 30x30mmHobbyWing XRotor Convertible F7 65A Stack with F7 Flight Controller HD DJI Plug and Play and 65A HW ESC 30x30 Featuring the new Hobbywing convertable F7 flight controller which is equipped with STM32F722 MCU and has powerful computing ability. Plus fast running speed, and high sensitivity ICM20602 six axis motion sensor. It can perfectly support bidirectional D Shot digital throttle communication. The integrated OSD chip can adjust and set each OSD
HobbyWing XRotor Convertible F7/65A Stack with F7 Flight Controller HD DJI Plug and Play and 65A HW ESC- 30x30
Featuring the new Hobbywing convertable F7 flight controller which is equipped with STM32F722 MCU and has powerful computing ability. Plus fast running speed, and high sensitivity ICM20602 six-axis motion sensor. It can perfectly support bidirectional D-Shot digital throttle communication. The integrated OSD chip can adjust and set each OSD parameters in FC parameter adjustment software and radio, which is simple and convenient. On-board large capacity Flash memory chip can record and store more flight logs, which is convenient for users to debug aircraft based on flight data.
Check out all our Stacks and the rest of our HobbyWing Products!
Replacement Flight Controller and 60A Electronic Speed Controller available!
By adopting the open-source AM32 firmware, the XRotor FPV G2 45A & 65A 4-in-1 ESCs benefit from faster update cycles and continuous feature expansion, compared to the closed-source BLHeli-32 firmware. Besides, enhanced compatibility and stability gain ensure exceptional and consistent performance for FPV drone racing.
Higher Power, No Load Worries
The AM32 firmware enables ESCs of the same specifications to sustain higher power output, handling high-load scenarios with ease and providing stronger power support.
Precision Tuning, Quicker Throttle Response
The motor KV value can be entered on the tuning page to finely adjust the motor's response speed and low-RPM acceleration, ensuring more precise control.
XRotor FPV G2 45A & 65A electronic speed controllers adopt next-generation 32-bit ARM F4 MCU running at 120 MHz for ultra-fast computation. In further, these ESCs support variable PWM Refresh Rate from 48 kHz to 96 kHz with dynamic auto-adjustment, delivering smoother throttle control.
Highly integrate four high-performance ESCs in one, XRotor FPV G2 45A & 65A ESCs feature built-in voltmeter which allows flight controllers to monitor the amp and voltage in real time. The shock-absorbing design of mounting holes effectively reduces the external vibration’s impact on high-sensitivity components and provides great shock-absorbing protection to upper devices (i.e. FC).
FC Specifications:
- Compatible with (Multirotors) Quadcopters
- Firmware HOBBYWING_XROTORF7CONV
- FC Programming Supported
- Programming via Betaflight/ Cleanflight-configurator
- Compatible with (Modes) PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, PROSHOT1000
- Compatible with (Transmitters) PPM, Spektrum, SBUS, SUMD, SUMH, XBUS, IBUS, JETIEXBUS, CRSF, SRXL
- OSD Built-in
- Voltage Monitoring Supported
- Current Monitoring Supported
- External Buzzer Supported
- LED Control Supported
- BEC 5V @ 1.5A ; 10V @ 1.5A
- Size 32x32mm
- Weight 3.3g
ESC Features:
- High-performance next-generation 32-bit ARM F4 MCU running at 120 MHz for ultra-fast computation.
-
open-source AM32 firmware
- All codes use damped light mode. Damped light does regenerative braking, causing very fast motor retardation, and inherently also does active freewheeling.
- The code supports features to prevent sync loss. There are tunable parameters that can make the code run well even in the most demanding situations, although default settings will work excellently in normal operating environments.
- The code supports regular 1-2ms pulse width input, as well as Oneshot125 (125-250us), Oneshot42 (41.7-83.3us) and Multishot (5-25us).
- Dshot signaling is supported at any rate up to at least Dshot1200. The input signal is automatically detected by the ESC upon power up.
- The code also supports a beacon functionality, where the ESC will start beeping after a given time of zero throttles. This can be very useful for finding lost crafts.
- Onboard 10V &5V BEC, powering different accessories such as FC, VTX, Camera and LED lights and etc.
ESC Specifications:
- LiPo Power input: 3S-6S
- Cont.Current: 65Ax4
- Burst Current: 80Ax4
- BEC Output: 5V@ 0.5A
- Input wires: 12AWG-130mm* (Red/Black)
- Output Wire: No wires but solder tabs
- Connectors: (In/Out) XT60 (w/ Wires Soldered on) /no
- Weight / Size: 15.0g / 32.7x18.4x6.2mm
- Mounting holes: 30.5x30.5mm
- Throttle Calibration: Supported
- ESC Programming: AM32
Package Includes:
- 1 x HobbyWing XRotor Convertible F7/65A HD AM32 Stack DJI PNP - 30x30mm
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy